|
Specifications
|
Gas Handling
|
|
|
| Reactant Gas Control: |
Mass Flow Controller |
|
| Maximum Number of Recatant Gases: |
Total of four gas channels divided between the fuel and oxidant channels as specified |
|
| Input Reactant Gas Pressure Range: |
100-170 psi |
|
| Purge Inlet Pressure Range: |
100-130 psi |
|
| Purge Valve: |
Normally open, computer controlled valve |
|
| Tail Gas Phase Separator: |
Optional |
|
| Tail Gas Back Pressure Control: |
Optional, manual or computer controlled available |
|
|
Electronic Load
|
|
|
| Type: |
MOSFET variable resistance load bank |
|
| Current Measurement: |
Panel shunt |
|
| Maximum Current Rating: |
5 Amp or 50 Amp |
|
| Maximum Voltage Rating: |
5, 10, or 20 Volts (Other voltages available, contact sales) |
|
| Maximum Power Dissipation: |
250 Watts |
|
| Nominal Short Circuit Resistance: |
< 1.25 milliohm |
|
| Corrosion Protection: |
All critical components gold plated |
|
|
Electrical Requirements
|
|
|
| Voltage: |
85-250 VAC |
|
| Frequency: |
47-440 Hz |
|
| Power Consumption: |
350 Watts plus power consumed by fuel cell heater switched receptacle |
|
|
Cell Heater Switched Receptacle
|
|
|
| Voltage/Frequency: |
Same as main power unit |
|
| Max. Current: |
3.5 Amps |
|
| Control Input: |
Type K thermocouple |
|
|
Installation Requirments
|
|
|
| Clearance for Operation: |
Back: 6", RH: 6", LH: 6", TOP: 0" |
|
|
Physical Characteristics
|
|
|
| Dimensions: |
29"D; 21.5"H; 12"W |
|
| System Weight: |
65-80 lbs. (depending upon options) |
|
| Operating Environment: |
40 to 100 Fahrenheit, 85% RH |
|
| Cabinet Rating: |
Indoor |
|
|
Front Panel Displays/EM>
|
|
|
| Fuel Cell Voltage: |
3-1/2 digit LCD backlit display |
|
| Fuel Cell Current: |
3-1/2 digit LCD backlit display |
|
| Back Pressure(s) Target (optional): |
0-100 psi analog gauge |
|
| Back Pressure(s) Actual (optional): |
3-1/2 digit LCD backlit display |
|
| Emergency Stop Indicator: |
Flashing Red LED |
|
| Gas Pressure Status Indicator: |
Green LEDs |
|
| Purge Pressure Indicator: |
Green LED |
|
|
Front Panel Connections
(all mating connectors provided) |
|
|
| Fuel Feed to Fuel Cell: |
1/4" Swagelok quick connect |
|
| Fuel Return from Fuel Cell: |
1/4" Swagelok quick connect |
|
| Oxidant Feed to Fuel Cell: |
1/4" Swagelok quick connect |
|
| Oxidant Return from Fuel Cell: |
1/4" Swagelok quick connect |
|
| Load Connections: |
Banana jack, scre, or bolt-on |
|
| Fuel Cell Voltage: |
LEMO (3' mating cable provided) |
|
| Fuel Cell Temperature Input: |
Mini Type K (thermocouple provided) |
|
| Auxiliary I/O: |
LEMO (3' mating cable provided) |
|
| Auxiliary Temperature Inputs (mating connector provided): |
2 Mini Type K thermocouple inputs |
|
| Switched Receptacle Output: |
IEC-320 output (mating cord provided) |
|
| Back Pressure Monitoring Port(s) (optional): |
1/8" Swagelok |
|
|
Back Panel Connections
|
|
|
| Reactant Gas Inlets: |
1/4" Swagelok |
|
| Tail Gas Discharge: |
3/8" Swagelok |
|
| Water Discharge (optional): |
1/8" Swagelok |
|
| Control Air Input (if required by options): |
1/4" FNPT |
|
| RS-485 Communication In/Out: |
DB-9 |
|
| Hardwired E-Stop Input: |
4 pin connector (jumpered mate, mating housing & sockets provided) |
|
| Hardwired E-Stop Output: |
4 pin connector (mating housing & pins provided) |
|
| SafeState Remote Input/Output: |
7 pin connector (jumpered mate provided) |
|
| Power Inlet: |
IEC-320 (mating cord provided) |
|
|
Software
|
Fideris
FCPower
TM
software. |
|
|
|
Photographs
|
|
|
|